Description:
Rockhard™ Table Top Urethane Varnish is the coating you need when you want a hard finish
that will deliver maximum resistance to water, alcohol, food stains, chemicals, detergents, and other damaging liquids.
This abrasion resistant finish is ideal for using on table tops as its name boldly proclaims. Its toughness makes it suitable for a multitude of other uses like wooden chairs, benches, desks, dressers, chests of drawers, vanities, bookcases, and many more.
Rockhard™ Table Top Urethane Varnish
is a high quality urethane fortified varnish which develops a hard, solvent resistant finish.
Sets to dust free in about 4 hours, dry to handle in 14 hours. Recoat in 14 hours.
Rockhard™ Table Top Urethane Varnish is designed for interior use only.
Advantages:
1 - Self Sealing
2 - New! Satin Sheen
3 - LOW VOC formula is compliant in most districts.
(in California, for SCAQMD, We suggest using H. Behlen WATERBORNE Rockhard™ Brushing Varnish
B603-21606 - Semi-Gloss, B603-21406 - Satin, B603-21206 - Flatt)
Directions:
WOOD PREPARATION:
Open grain may be filled with Behlen Pore-O-Pac™ or Water Base Grain Filler.
Sand raw wood with 150 – 180 grit sand paper and remove dust. Stain sanded wood with Behlen Solar-Lux™ Stain, Behlen15 Minute pigmented Wiping Stain or Behlen Solar-Lux™ Waterborne Stain. Allow required drying time for each type of stain.
MIXING: --- Do NOT Shake.
Mix thoroughly with a paddle, as vigorous shaking would generate air bubbles that could become trapped in the dried film. Rockhard™ Table Top Urethane Varnish is supplied at brushing consistency and is self sealing.
APPLICATION: It is recommended that a good natural bristle brush be used for
Rockhard™ Table Top Urethane Varnish. Best results are obtained when thin uniform coats are applied with the grain.
Do not over-brush by going back and forth several times.
Scuff sand with P320A – P400A Silicon Carbide Stearate Dry sandpaper between coats.
One quart covers approximately 125 sq. ft. Allow 48 hours dry time before use.
RUBBING: Depending on drying conditions and the thickness of finish applied,
allow at least 72 to 96 hours drying time before rubbing.
CLEANUP: Use minerals spirits or Paint thinner
Safety and Other Precautions: Read MSDS for precautions before using product.
Specifications:
Gloss – M603-28806
Weight per gallon: 8.01 lbs/gal
Solids % (wt): 49.3
Solids % (vol): 48.04
Dry time: Air dry @ 72°F, 35% rel. humidity
Dust free: 4 hours
To handle and recoat: 14 hours
To use: 48 hours
To rub: 72 – 96 hours
VOC's (coating): 3.02 lbs/gal (363.20 g/l)
VOC's (material): 2.64 lbs/gal (317.42 g/l)
VHAP's: 0.0001 lbs VHAP's/lbs solids
Coverage: 770 square ft/gal @ 1 mil thickness
Package Life: 3 years unopened
Satin – M603-28406
Weight per gallon: 8.91 lbs/gal
Solids % (wt): 33.77
Solids % (vol): 35.72
Dry time: Air dry @ 72°F, 35% rel. humidity
Dust free: 4 hours
To handle and recoat: 14 hours
To use: 48 hours
To rub: 72 – 96 hours
VOC's (coating): 3.02 lbs/gal (362.31 g/l)
VOC's (material): 1.96 lbs/gal (234.77 g/l)
VHAP's: 0.0126 lbs VHAP's/lbs solids
Coverage: 572 square ft/gal @ 1 mil thickness
Package Life: 3 years unopened
All values theoretical; not intended to be exact QC specifications.
HMIS: Health –
1, Flammability – 2, Reactivity – 0, Personal Protection – X
SDS: If a Safety Data Sheet is required, contact: info@shellac.net
• • • • •
